REJEX VS ULTIMA PAINT GUARD PLUS PLUS
REJEX VS ULTIMA PAINT GUARD PLUS FREE

Curing is required to allow the monomers (polymer building blocks) that make up RejeX to attach to the surface being treated and to cross-link into a crystal-clear, impervious film. RejeX is wiped on, allowed to dry to a haze for approximately 20 minutes, wiped off, then allowed to cure for 8-12 hours (depending on the humidity the higher the humidity, the faster the cure). If the surface is too hot, the coating can cure before it has properly bonded to the surface, so it may not perform up to its potential. When over 85° F, be sure to apply RejeX out of direct sunlight. Ideally, RejeX should be applied to a cool, dry, clean surface.

REJEX VS ULTIMA PAINT GUARD PLUS FREE

RejeX contains none of the free silicone oils found in some other products that are known to contaminate paint and cause problems when repainting. It’s easy to apply and produces a deep, lustrous shine that outlasts the most popular waxes by months.

It also makes graffiti easy to remove and can be applied to windshields to repel rain. This very thin film – less than a micron thick – prevents stains and adhesion of common contaminants such as exhaust, bugs, oil, tree sap, bird droppings, road grime, brake dust, etc. RejeX® is a thin-film polymer coating designed to provide a high-release protective finish for vehicles of all kinds. One coat every 12 hours.SPACE AGE PROTECTION FOR YOUR CAR, TRUCK, BOAT, RV, AIRPLANE & MOTORCYCLE If there is going to be a little dust on the car then I would qd with Ultima QD spray and then add next coat. It is a little disconcerting not always being able to tell if you are putting anything on your paint.Īssuming you have a garage that isn't dusty you can place the second coat after 12 hours. I didn't have any trouble at all even the first time but I have read some people apply too much.

It will come out great if you don't over apply. In the unlikely chance that their is a streak somewhere after 12 hours of curing simply take some Ultima QD and spray and wipe the streak with a high quality MF towel.Įven though on some colors or in some lighting it seems like you aren't putting anything on your paint just TRUST the product. This is not a product that you have to buff off. There should be no need to do anything else. Now just DO NOT touch Wait 12 hours and inspect. Their may or may not be a slight film on the paint for a bit but it starts it's bonding process immediately. When you are no longer sure if anything is on the pad touch your clean window with it and you'll be able to see if there is still product on the applicator.ĥ.-If I don't see anything then its time for (1) more spritz to the applicator.Ħ.-Repeat until you get to the last panel.

Then I'll wipe over to the side a bit where I know I haven't applied any to see if there is still anything coming off the pad. I basically make sure I do about 3 SQ FT. But on certain colors and without really good lighting its sometimes hard to tell anyway. Another thing to look for is that your applicator is no longer leaving anything on the paint. I always finish with straight lines from front to back of the panel. You are not polishing so no need to rub too hard or over and over. Apply the UPGP by hand and follow the directions! Below is my method which should not contradict the instructions you receive with the product.Ģ.-Take a clean microfiber applicator and spray 1 spray onto it to prime it.ģ.-Spray it once more and do about a 3 SQ FT area.Ĥ.-Apply in circular motions just making sure to overlap and cover the entire area. The mistake people make is they apply too much. If you don't then you should clean the paint after polishing so the UPGP bonds properly.

REJEX VS ULTIMA PAINT GUARD PLUS PLUS

Ultima Paint prep plus works as a light polish but also leaves behind a primer for the UPGP. I love all the Ultima products I've used. It is so easy to apply that it just makes sense to apply more often. I like to apply any sealant quarterly (every 3-4 months) here in FL for maximum protection. I would say that durability is around 4-5 months. I have UPGP from 2008 and have spoken to the manufacturer and they say that its fine. It allows for covering larger surface area in one swipe and is easier to grip while applying. I really love the stuff.Īny applicator will work, but the supplied microfiber applicator is ideal. Ultima Paint Guard Plus is my 'go to' sealant. Tried doing a search or at least I think I did but did not get much info on it. What is its shelf life? I read somewhere that it expires in 2 years is this true?Ĭan I also get your opinions on durability? Hi guys, I plan to use UPGP for the first time in a the next few weeks and wanted to ask for some tips on application and have other questions as well.Ĭould I use an ordinary foam pad like the Meguiar's yellow foam pad or do I really have to use the supplied microfiber pad?

Rejex vs ultima paint guard plus